A Method for Calculating Dynamic Load of Suspension Part Based on Udwadia-Kalaba Theory

HU Sanbao, WU Pan,WANG Chao

Abstract

Based on Udwadia-Kalaba theory，a method for calculating the dynamic load of suspension part was studied by taking the six-component force of wheel center as the input. Taking the five-rod rear suspension as the modeling object，the dynamic model of the suspension system was established，and the analytical expression of the load at each part was obtained with the decomposition of the total binding force. Compared with the traditional Lagrange modeling method，the method does not need the Lagrange multiplier and reduces the complexity of modeling. In order to verify the correctness of the method，the numerical results were compared with the simulation results of the traditional modeling software Adams/Car. The analysis result shows that the proposed method is accurate and efficient，and the calculated dynamic loads are in good agreement with the Adams/Car simulation results. Finally，the method was applied to the actual vehicle test，and the load prediction for the rear suspension of a SUV was carried out.

 

 

Keywords: suspension part,  Udwadia-Kalaba theory,  six-component force,  dynamic load, load prediction


Full Text:

PDF


References


ENSOR D, COOD C, BIRTLES M. Optimising simulation and test techniques for efficient vehicle durability design and development [C]//2005 the Automotive Research Association of India. Pune: SAE, 2005:26—42.

CHENG Y G, ZHENG S L, FENG J Z, et al. Study on optimization of durability test load spectrum of car suspension [J]. Automobile Engineering, 2009, 31(5):467—470. (In Chinese)

QING H J, HAN X, CHEN Z F, et al. Collection and analysis of structural load spectrum of a car [J]. Journal of Hunan University (Natural Sciences), 2012, 39(12):32—36. (In Chinese)

ZHANG S H, LIU J, LIU Y J. Fatigue analysis of the cubframe of a passenger vehicle based on the load spectrum extracted by the six– component force Meter [J]. Agricultural Equipment and Vehicle Engineering, 2017, 55(6):49—53. (In Chinese)

CAO J. Fatigue durability analysis of a SUV white body[D]. Changchun:College of Mechanical Science and Engineering, Jilin University, 2016: 19—26. (In Chinese)

GU Z Q,ZANG X L,BU B G,et al. Fatigue life analysis and structure optimization of lifting mechanism of mine barrier cleaning vehicle [J]. Journal of Hunan University (Natural Sciences), 2014, 41(2):58—63. (In Chinese)

S,BANG J Q,et al. Load decomposition method based on wheel senter six–component force [J]. Computer Assistant Engineering, 2013, 22 (S1):60—64. (In Chinese)

LI Y J. Simulation analysis of missile separation based on FLUENT and ADAMS[D]. Harbin:College of Aerospace, Harbin Institute of Technology, 2012: 28—38. (In Chinese)

ZHAO H, ZHEN S C, CHEN Y H. Dynamic modeling and simulation of multi–body systems using the Udwadia–Kalaba theory [J]. Chinese Journal of Mechanical Engineering, 2013, 26 (5): 839—850.

HUANG D, DUAN S L, ZHEN S C, et al. Dynamic modeling and analysis of heavy duty vehicle based on system constraints [J]. China Mechanical Engineering, 2017, 28 (4): 478—486. (In Chinese)

JIANG J M. Research on automatics slutch combination control based on adaptive fussy control of variable range domain and Udwadia – Dalaba theory [D]. Hefei: College of Automotive and Traffic Engineering, Hefei University of Technology, 2017: 65—78. (In Chinese)

ZHAO R Y, JIAO S J,BANG X. Dynamic modeling method of multi –finger robot [J]. Journal of Chang´an University (Natural Sciences), 2015, 35(3):151—158. (In Chinese)


Refbacks

  • There are currently no refbacks.