Thermal Stress Analysis of Bearing Body Based on Research of Turbocharger Overall Heat Transfer

GONG Jinke, BU Yanping, ZHONG Chao, HU Liaoping, CHEN Shaolin

Abstract

Based on coupled heat transfer theory, a model of turbine box with waste gate was built, and turbine box, heat shield and bearing body was tied as an assembly to be heat transfer analyzed. Temperature and thermal stress analysis of bearing body were then obtained. The results show that temperature is gradually reduced from turbine box to bearing body, which presents an obvious temperature gradient. And the temperature of turbine box is about 71.5℃ lower than original gas temperature. Because of good insulation of heat shield and dual cooling of cooled water and oil, the temperature of bearing body is low. However, the thermal stress of bearing body is high due to its temperature difference between inside and outside surface. Compared with the test results, the maximum deviation between the simulated and experimental value is 7.2%, which verifies that this simulation method has high precision and can provide a theoretical basis for the design and optimization of turbocharger.

 

Keywords: turbine box,  heat shield,  bearing,  coupled heat transfer,  thermal stress


Full Text:

PDF


References


LIN H С. CHANG Y T. LONG T G. et al. Oil coking prevention using electric water pump for turbo-charge spark-igni-tion engines [JJ. Mathematical Problems in Engineering, 2014 (6):l 8.

I G S. BI J G, WANG Y F, et al. A preliminary discussion on the characteristics of turbocharger for gasoline enginc [j]. Automobile Applied Technology. 2016(8):85 - 87. (In Chinese)

BURKE R D. COPELAND C D. DUDA T. et al. Lumped capacitance and three-dimensional computational fluid dynamics conjugate heat transfer modeling of an automotive turbocharger [J]. Journal of Engineering for Gas Turbines and Power. 2016. 138(9): 92602-92601.

GONG J K. ZHANG T. HU L P. et al. A research of the simulation on the cooling performance of water-cooled bearing in turbocharger[J]. Automotive Engineering. 2014.36(3). 383 - 388. (In Chinese)

HEUER T. ENGELS B. WOLLSCHEID P. Thermomechanical analysis of a turbocharger based on conjugate heat transfer [C]//Proceedings of ASME Turbo Expo 2005. Reno-Tahoe. Nevada. USA. 2005:829-36.

GONG J K. TIAN Y H, JIA G H. Et al. Numerical simulation on coupled heat transfer of turbocharger bearing [J]. Journal of Hunan University(Natural Sciences) .2015. 12(1): 7-12. (In Chinese)

ZHANG Y G. MAO H P. SU T X. Numerical simulation based overall discrete method for thermo-fluid-solid coupling of cylinder head[j]. Transactions of Beijing Institute of Technology, 2016.36 (6)s563-568. (In Chinese)

ZHAO Y R. The coupling heat transfer research on piston group-liner-coolant of engine[l]. Taiyuan: North University of China. 2016: 43 -45. (In Chinese)

JIA L. FANG Z H. QIAN X H. Higher heat transfer[M]. Beijing: Higher Education Press. 2008:1 17- 125. (In Chinese)

LAUNDER B E. SPALDING D B. Lectures in mathematical models of turbulence [M]. London: Academic Press. 1972.

LI F Z. TONG S G. YUAN M II. Multi-objective optimization for turbocharger housing considering thermo-fluid-solid interaction [j]. China Mechanical Engineering. 2016. 27 (6) : 754 - 766. (In Chinese)

WU X T. HE H. XU S Y. et al. Heat transfer calculation method of turbocharger bearing[J]. Vehicle Engine. 2010,186 (1) : 11-14. (In Chinese)


Refbacks

  • There are currently no refbacks.